Settings Database

Official Ortur recommendation: 15000mm/min (250mm/s) at 100% power.

Community-verified OLM3 20W basswood engrave.

2 passes for birch plywood at 20W. Air assist required.

6mm acrylic single pass on 60W.

OLM3 20W cuts 3mm in 1 pass. Air assist critical.

High power, moderate speed for good slate contrast.

2 passes for 6mm. Air assist clears smoke between passes.

6mm acrylic on 100W — lower power, good speed.

Thunder 60W anodized aluminum.

Low air for acrylic — high air blows melt back.

60W CO2 cuts acrylic with flame-polished edge.

Frosted white on clear cast acrylic.

Leather engrave at 20W. Rich dark marks.

Standard basswood engrave. Good contrast.

Good leather engrave at moderate settings.

High power for anodized on diode.

AP Lazer 100W 6mm acrylic single pass.

AP Lazer open architecture allows large granite slabs and headstones.

Open design lets AP Lazer work on objects of any size.

Production engrave speed on 100W machine.

Clean cut on veg tan.

Thunder can engrave up to 1000mm/s. 500mm/s is production-safe.

AP Lazer 100W cuts 3mm basswood with ease.

AP Lazer recommends 3" lens for acrylic — cleaner edges on thick stock.

Lower power, higher speed. Cast acrylic gives frosted finish.

100W cuts 6mm birch cleanly.

Single pass on veg tan.

Single pass on veg tan leather.

Dark acrylic cuts well with air assist.

Built-in air assist — use it.

Cuts 3mm basswood in 1 pass. Comparable to Sculpfun S30 Pro Max.

6mm basswood requires 2 slow passes at 20W.

Good anodized marking at high power.

6mm requires 2 passes. Slightly slower than Sculpfun in comparison tests.

High power for anodized marking on diode.

Single pass on veg tan. Air assist reduces char.

High power with moderate speed for polished edge.

AP Lazer 100W cuts 3mm acrylic cleanly.

Production engrave at 100W. Very fast.

Very low power on high-wattage machine for leather.

100W handles 6mm easily in 1 pass.

100W cuts 3mm basswood fast. Lower % preserves tube life.

White on dark slate. Excellent for personalized gifts.

Thunder 60W leather engrave — low power, moderate speed.

Enable M8 in LightBurn for automatic air assist control.

S30 Pro Max cuts 3mm in 1 pass. Excellent focus retention vs. competitors.

Opaque acrylic only — diode cannot cut clear.

3 passes on dark acrylic at 20W. Air assist keeps edges clean.

100W anodized aluminum — lower power needed vs. 60W.

60W cuts 6mm in 1 pass on Thunder.

Reduce from factory defaults — factory settings typically run too hot.

Low air assist to prevent melt blowback.

Boss 65W 1/4" acrylic cut.

Boss 65W veg tan leather engrave.

Boss 65W birch engrave.

Boss 65W basswood engrave. Low power for clean marks.

Boss 65W leather cut.

Boss 65W 1/8" basswood cut.

Official Rabbit Laser 40W wood engrave.

Official Rabbit Laser 40W 1/4" acrylic. Near full power required.

Slight defocus.

Official Rabbit Laser 60W granite.

Official Rabbit Laser 60W thin leather cut.

Official Rabbit Laser 40W 1/8" basswood. Higher % at lower wattage.

Official Rabbit Laser 60W leather engrave.

Official Rabbit Laser 40W thin leather cut.

Official Rabbit Laser 60W anodized aluminum.

Official Rabbit Laser 40W anodized aluminum.

Boss 65W anodized aluminum mark.

Do not engrave through coating — exposed metal may rust.

Official Rabbit Laser 80W powder coat.

Official Rabbit Laser 60W 1/8" basswood cut.

Boss 65W 1/8" birch cut.

Official Rabbit Laser 60W wood engrave.

Power varies by anodize color — black requires lower power.

Official Rabbit Laser 80W anodized aluminum.

Defocus target slightly for granite.

Official Rabbit Laser 80W granite. Rub paint into cracks for contrast.

Set scan gap for your required resolution.

Official Rabbit Laser 80W leather engrave.

Official Rabbit Laser 60W birch plate.

First pass to near backing, second to finish. High air assist.

Excessive heat boils mirror backing. 2 passes required.

Lowest power with highest speed.

Official Rabbit Laser 80W 1/16" leather cut.

Lowest power with highest speed.

Official Rabbit Laser 80W 1/8" birch plate.

Official Rabbit Laser 80W 3/16" birch plywood.

Apply masking tape to prevent sap haze.

Official Rabbit Laser 80W wood engrave.

Slightly lower power than 60W machine for same result.

Do not go too slow — surrounding acrylic will sag or catch fire.

Official Rabbit Laser 80W 1/4" acrylic cut.

Keep glass cold with cold air, wet paper, or coating.

Official Rabbit Laser 80W. Use lowest power with thin scan gap.

Thunder 60W cuts 3mm basswood in single pass. Clean edge.

Boss 100W leather engrave.

Lowest power with highest speed for clean cut.

Official Rabbit Laser 80W 1/8" basswood cut.

Boss 100W 1/4" acrylic cut.

Boss 100W anodized aluminum.